在基于长城的GF7280V5的arm64服务器中安装驱动时，提示不支持当前的内核版本，但是安装时默认最老是6.6.0-32.7.v2505.ky11.aarch64， 更新下系统变更为6.6.0-32.21.v2505.ky11.aarch64，而想将内核从麒麟V11的归档库中降级到6.6.0-32.6.v2505.ky11.aarch64，却因为没有归档了，无法降级，导致无法安装沐曦驱动，是否能提供下支持上述内核版本的沐曦C500的驱动？
沐曦驱动安装报错：
[xxx@localhost softwares]$ sudo ./metax-driver-3.8.0.10-rpm-aarch64.run -- -f
Verifying archive integrity... 100% MD5 checksums are OK. All good.
Uncompressing MetaX driver installer 100%
rpm/mxfw_.rpm
rpm/mxsmt_.rpm
rpm/metax-linux[-_]*.rpm
installing packages under /opt/mxdriver
installing rpm/mxfw_3.8.0-1.noarch.rpm
Verifying... ################################# [100%]
Preparing... ################################# [100%]
Updating / installing...
1:mxfw-3.8.0-1 ################################# [100%]
installing rpm/mxsmt_3.8.0-1.aarch64.rpm
Verifying... ################################# [100%]
Preparing... ################################# [100%]
Updating / installing...
1:mxsmt-3.8.0-1.ky10 ################################# [100%]
installing rpm/metax-linux-3.9.10-1.aarch64.rpm
Verifying... ################################# [100%]
Preparing... ################################# [100%]
Updating / installing...
1:metax-linux-3.9.10-1 ################################# [100%]
Notice: The current kernel version (6.6.0-32.7.v2505.ky11.aarch64) is not supported.
The list of supported kernels is as below:
4.18.0-240.el8.aarch64
4.19.90-2107.6.0.0220.22.oe1.bclinux.aarch64
4.19.90-2112.8.0.0131.oe1.aarch64
4.19.90-2304.4.0.0198.oe1.aarch64
4.19.90-2305.1.0.0199.56.uel20.aarch64
4.19.90-2403.3.0.0270.95.d.7.uel20.aarch64
4.19.90-2412.3.0.0308.u208.fos22.aarch64
4.19.90-24.4.v2101.ky10.aarch64
4.19.90-25.063.vlx67.v99_2003.sg.aarch64
4.19.90-25.10.v2101.ky10.aarch64
4.19.90-25.17.230.po1.aarch64
4.19.90-52.22.v2207.ky10.aarch64
4.19.90-52.23.v2207.gfb08.ky10.aarch64
4.19.90-52.23.v2207.gfb10.ky10.aarch64
4.19.90-52.40.v2207.gfb14a.ky10.aarch64
4.19.90-85.0.v2307.ky10.aarch64
4.19.90-89.11.v2401.ky10.aarch64
4.19.90-89.25.v2401.gfb01.ky10.aarch64
4.19.90-89.5.v2401.ky10.aarch64
5.10.0-136.108.0.188.u167.fos23.aarch64
5.10.0-136.54.0.133.oe2203sp1.aarch64
5.10.0-153.12.0.92.oe2203sp2.aarch64
5.10.0-182.0.0.95.oe2203sp3.aarch64
5.10.0-216.0.0.115.kb5.ky3_5.aarch64
5.10.0-216.0.0.115.kb83.ky3_5.aarch64+64kb
5.10.0-298.0.0.200.ile2312sp1.aarch64
5.10.0-60.67.0.116.ule3.aarch64
5.15.0-1.10.6.v2307.ky10h.aarch64
5.15.0-1.18.v2307.ky10h.aarch64
5.15.131-19.cl9.aarch64
5.15.131-26.cl9.aarch64
5.15.131-29.cl9.aarch64
5.4.241-24.0017.26
6.6.0-28.0.0.34.kb20.ks6.aarch64
6.6.0-32.0.v2505.ky11.aarch64
6.6.0-32.6.v2505.ky11.aarch64
6.6.0-72.0.0.76.oe2403sp1.aarch64
6.6.0-72.0.0.76.ule4.aarch64
And then reinstall the metax-linux package.